Morn Packaging Co., Ltd.
en
Share Some Common Knowledge of Plastic Woven Bag Coating

Share Some Common Knowledge of Plastic Woven Bag Coating

The coating is an important process in the production of plastic woven bags, and it is also a process prone to slippage. So when it comes to this kind of problem, how can we ensure the safe completion of plastic woven bags coating? To help you solve these problems, our customer manufacturers share some common sense with you based on years of experience.

Align the cots as far as possible in the middle of the cots before winding, and coat the ends of the cots with silicone oil before plastics woven bag coils enter the car. When you are receiving and laying the cloth, the synchronous speed drop is less than 30 meters per minute. Clamp rollers before receiving cloth. Don't forget to stick tape. After inserting the cloth, look at the edge of the cloth to align and correct the deviation of the optoelectronic eye, then lift the clamping roll, and connect the new cloth. The width of the cloth changes. It is necessary to observe the edge of the cloth and adjust the die edge. The speed is slightly slower before the cloth is connected. After splicing, before the double-layer joint enters the corona, the corona machine should be closed first. After the double-layer joint enters the composite roll, the edge cutter should be raised and the blower should be opened. After the joint, the edge should be cut and closed.

When the joint is rolled up, change the roll in time. In the first class before an operation, adjust the cutting width as soon as possible before going through the fabric and connect the plastic woven bags. The tension of releasing, winding, the temperature of preheating roll, corona voltage, and coating speed ratio is adjusted well. After the introduction of new cloth, the temperature of the cold roll is low, and the speed of the car should not be higher than 35 meters per minute. Close the cooling roll before starting, wait for the surface temperature of the cooling roll, and then open the cooling water valve. Control the surface temperature of the cooling roll (40-50 degrees Celsius) and adjust the tension of unwinding and winding. Avoid the appearance of bell mouth and waste plastic woven bags in rewinding, and two touch bell sound prompts. Paper strips are used as markers to indicate that the following processes, including defective coating, blistering, film opening, edge breaking, and other defective products and waste products, should be marked. If the flatness of plastic woven bags is poor, the release tension will be increased when lotus leaves appear. Before coiling the cloth, the length of the end of the coil and the core iron pipe should be confirmed.

After the cloth is put on, observe the position of the cloth roll and keep it as close as possible to the middle of the cots. If there is too much in the middle of the offset, roll down and turn around in time. Prevent from being unable to rectify the deviation because the rectification journey is in place. In the process of coating, the corona machine, preheating and cooling roll water valves should be shut down in time when the car is withdrawn due to some reasons. After entering the car, open it one by one. When plastic woven bags have serious lotus leaf edges, do not put them on the operating surface to correct the deviation. When the unwinding tension is increased properly, the tension of the plastic woven bag roll should be released after the winding diameter of the plastic woven bag roll is reduced (if it is a manual shield). When changing specifications, the surface of the rubber roll and the pressing roll should be decontaminated first. Before the coating material is poured into the mixer, the dust on the outer skin of the packaging bag should be cleaned first. In the mixing process, the paint should be kept clean, dust should be avoided from entering the hopper. You should regularly inject oil into the gas-source triad and you need to drip oil for the wheel and pneumatic track.
Related News
  • In the First Half of the Year, PP Market

    In the First Half of the Year, PP Market

    July 9, 2019I. Review of TrendsThis year, the overall performance of the domestic polypropylene market is not good. The market is in a volatile and declining trend. In the first quarter, terminal demand did not s...view
  • An Environmental Protection Internal Coating Technology for Plastic Woven Bags

    An Environmental Protection Internal Coating Technology for Plastic Woven Bags

    July 9, 2019Woven bags are usually made of cross-woven silk, with tiny seams at the cross of the knitted silk. Therefore, polyethylene resin is usually used to coat the surface of woven bags. The manufacturing me...view
  • The Use of the Bopp Rice Bags

    The Use of the Bopp Rice Bags

    May 28, 2019Bopp rice bags bring us many conveniences in life. Therefore, bopp rice bags are becoming more and more popular in our life, because they play a very important role in our life.1. Save timeIf you need...view
  • Technological Process Of Plastic Pp Woven Bag

    Technological Process Of Plastic Pp Woven Bag

    May 17, 2019Color printing pp woven bag is now the most common packaging materials, because the color printing pp woven bag can be printed on a variety of patterns, with a strong visual effect, color printing pp ...view
News
Latest news
Contact
Contact us
  • +86 (0)577 68805163
  • +86 (0)577 68805163
  • bag@wovenpp.com
  • Lingxi Industrial park, Cangnan, Wenzhou, Zhejiang province, China